First, the use of Huayu brothers snowflake ice machine:

1. Huayu Brothers Snowflake Ice Machine removes the outer packaging and removes the attached file bag and inlet pipe, drain pipe, ice spoon and other accessories from the storage refrigerator.

2. Place the ice machine in a ventilated place, keep a lot of space with the wall and 150mm away from the heat source. Make sure the machine is placed smoothly.

3. Attach the attached Ñ„12 soft plastic corrugated drain pipe to the outlet pipe on the back of the machine and the other end to the sewer port.

4. Connect one end of the attached water pipe to the tap of the tap water supply pipe, and the other end to the water valve threaded joint on the back of the ice machine. Note that when connecting, the seal ring should be placed at both ends of the inlet pipe (scheduled)

5. Unscrew the tap to ensure smooth flow of the inlet pipe.

6. Plug in the power plug and press the rocker switch on the operation panel. At this time, the ice machine starts working. The ice machine implements automatic continuous ice making from water inlet, ice making, dehydration and ice storage. If the amount of ice in the refrigerator reaches a certain level, the full ice light on the operation panel will light up, and the ice machine will only stop. When the external water supply pipe has water or water supply failure, the water shortage lamp on the operation panel of the ice machine will light up. The ice machine is stopped.

Second, Huayu brothers snowflake ice machine operation notes:

1. Regardless of the reason for the compressor (water shortage, excessive ice, power failure, etc.), it should not be started continuously. It should be restarted every 5 minutes to avoid damage to the compressor!

2. Regularly check the inlet and outlet connections to handle small amounts of residual water that may leak!

3. When the ice-breaking ice is not in use, drain the remaining water in the inner tank, dry the refrigerator inner liner with a clean cloth, screw off the drain connector cover at the back of the cabinet to drain the remaining water in the water tank, and then tighten. Sewage joint cover!

4. When the ambient temperature drops below O °C, there is the possibility of icing. Drainage must be carried out to release the water. Otherwise, the inlet pipe may be broken!

5. Unplug the ice machine when it is cleaned, inspected, and used for more than one week.

6. Drain pipes should be inspected 1 or 2 times a year to prevent blockage.

Third, the installation notes:

1. The ice machine should be installed away from the heat source, without direct sunlight, and the ventilation is good. The ambient temperature should not exceed 35 degrees Celsius to prevent the condenser from dissipating heat and affecting the ice making effect. The floor where the ice machine is installed should be solid and flat, and the ice machine must be level, otherwise it will cause no ice and noise during operation.

2. The gap between the back and left and right sides of the ice making machine should be no less than 30cm, and the top clearance should be no less than 60cm.

3, the ice machine should use an independent power supply, dedicated line power supply and equipped with fuses and leakage protection switches, and must be reliably grounded.

4. The water of the ice machine should meet the national drinking water standard, and a water filtration device should be installed to filter the impurities in the water to avoid clogging the water pipe and polluting the water tank and the ice mold. And affect the performance of ice making.

5. Carefully handle the ice machine to prevent severe vibration. The handling inclination should not be less than 45 degrees. After long-distance transportation, the ice machine should be placed for 2-6 hours before the mechanism ice can be opened.

6. When cleaning the ice machine, turn off the power supply. Do not use the water pipe to directly align with the body. Use a neutral detergent to scrub. Do not use acidic or alkaline solvents to clean.

7. The ice machine must unscrew the inlet hose head for two months to clean the inlet valve screen to prevent the sand mud impurities from clogging the water inlet, which causes the water intake to become smaller, resulting in no ice.

8. The surface of the condenser must be cleaned every two months. If the condensation is poor, the compressor components will be damaged. When cleaning, use a vacuum cleaner, a small brush, etc. to clean the condensed surface oil dust. Do not use a sharp metal tool to clean it to avoid damaging the condenser.

9. The water pipes, sinks, storage refrigerators and protective film of the ice machine should be cleaned every two months.

10. When the ice machine is not in use, it should be cleaned, and the ice mold and the moisture in the box should be dried with a hair dryer, placed in a place free of corrosive gas and ventilated and dry, to avoid open storage.